BWD Variable Speed Drive Booster Pump 1.1KW
R16,650.00 Original price was: R16,650.00.R14,500.00Current price is: R14,500.00.
Model: BWD5-40
Power: 1.1KW
Max Head: 85M
Optimal Head: 45M
Max Flow: 9.5 m3/h
Optimal Flow:5 m3/h
Inlet: 1.25” / 32mm
Outlet:1.25” / 32mm
Categories: Booster Pump Combo, Pressure Pumps, Variable Speed Drive, VSD Pump
Features & Benefits
Easy to Operate
- Intuitive controls for hassle-free use.
Low Noise Level
- Quiet operation ideal for residential and commercial settings.
Automatic Start/Stop Function
- Efficient automatic operation to save time and energy.
Pre-Wired with a 3-Point Plug
- Ready to use out of the box with minimal setup.
Energy-Efficient
- Achieves up to 80% energy savings compared to traditional pump systems.
Restart Delay
- Built-in 3-second delay protects the motor from heat build-up due to frequent on/off cycles.
Auto-Rotation
- Automatic timer starts the pump within a pre-selected cycle to rotate the bearings and ensure longevity.
Constant Pressure
- Pressure transducer maintains steady pressure even with multiple water outlets in use.
Class-Leading Efficiency
- Integrated protections against:
- Dry run
- Over-current
- Over/under voltage
- Overload
- Abnormal pressure
Pump Performance Curve
(Insert Performance Curve Graph Here)
| Flow Rate (Q, m³/h) | 0 | 2.0 | 4.0 | 6.0 | 8.0 | 10.0 | 12.0 | 14.0 | 16.0 | 18.0 |
|---|
Pump Specifications
| Model | Power (Kw) | H.max (m) | H.rated (m) | Q.max (m³/h) | Q.rated (m³/h) | Speed.max (rpm) | Voltage (v) | Frequency (Hz) | In/Outlet (Inch) |
|---|---|---|---|---|---|---|---|---|---|
| BWD5-40 | 1.1 | 85 | 45 | 9.5 | 5 | 5000 | 200 ± 20% | 50/60 | 1.25”×1.25” |
| BWD12-40 | 2.2 | 70 | 35 | 17 | 12 | 4500 | 200 ± 20% | 50/60 | 2”×2” |
Maximum Fluid Temperature: 80°C
Maximum Ambient Temperature: 40°C
Variable Speed Drive (VSD) Defined
The pump’s speed adjusts according to pressure requirements, ensuring minimal energy use.
Suitable Applications
- Clean water usage, including drinking water
- Non-potable water piping systems
- Irrigation purposes
- Compatible with water temperatures from 2 to 80 degrees Celsius
Important Information
- The pump must be earthed.
- Maintenance should be performed with the power supply disconnected.
- Avoid putting strain on the electrical cable.
- Designed only for clean water use.
- Carefully read and understand instructions before adjusting any settings.
- Extending the cable may void the factory warranty; use an approved extending plug adapter.
- Install in a ventilated, undercover area to protect from direct sunlight, rain, and irrigation spray.
- Pumping muddy water or water with suspended solids will shorten the unit’s lifespan and is not covered under warranty.
- Equipped with a draining screw at the bottom of the suction/discharge casing; drain the unit when temperatures fall below 0°C.
Operating Instructions
- Ensure the power supply cable is correctly connected.
- Use rigid piping for suction and discharge, able to withstand up to 6 bar pressure. Ensure airtight suction and watertight discharge.
- Follow the priming instructions as per the diagrams.
- Operate with a 230V single-phase power supply, with voltage variances no greater than ±10%